Installing front fender fenders on Renault Sandero.

Purchase and sales The vehicle's fender guards and ventilators are removed for cleaning and maintenance. body parts

Also for approaching certain nodes.

The car bumper is removed to replace it, as well as to replace other parts of the car.

Removal of breathers and fenders

For this task, you will need Torx keys T-20 and T-30, and a set of screws.

We install the car on a platform or inspection ditch

Before removing the bridle guard and fender guard, remove the outboard wheel

To remove the front wheel splash guard, tighten the bolt securing the splash guard to the body threshold

We tighten the two screws of the fastening to the front fender

We screw the fastening clamp to the cross-section of the body.

We take off the breeze block

We install a breeze shield at the gateway

Removing the front wheel fenders

Let's take out the breeze block, as described above

Can be screwed in and removed

We twist the pin “A” and, having tightened it with a twist, we lift the pin “B” that secures the front fender to the body.

Tighten the screw that secures the fender support to the front fender

Removable fender

We install the front fender in the turning order

Front bumper cover

Required keys for 10 and Torx T-30 and screws

We screw the three screws of the front bumper fastening and the lower part of the engine's breather guard right-handed

We screw in three screws securing the bumper

We recognize the cover, as described above in this article

Screw the three screws securing the bumper to the subframe

From the inner part of the bumper, use a chisel to cut three rivets securing the bumper to the body on both sides.

This is how the rivets securing the bumper to the body are removed.

In the front wheel arches, screw in one screw each, securing the bumper to the body

Screw the screws that secure the lining to the radiator frame.

The radiator lining was prepared in one piece with the front bumper. Known

front bumper

We install the front bumper at the turn.

Rear bumper removal

Required wrenches Torx T-30 and Torx T-20, head for 10 screws In the arches rear wheels

We screw one screw at a time securing the bumper to the body

We screw two screws from the bottom of the car, securing the bumper to the energy-absorbing element on the right and left sides.

After last winter, the idea came up to install rear fender fenders, because those that come from the factory with fender fenders cannot be called a word.

In short, it’s unimaginable.

At the same time, having removed and marveled at the front ones.

As a result, adding rear fenders - 600 rubles, vibration STP 5 l. 200 rubles sheet, a can of "cordon" + 2 cans of "bar'era" (I don't remember the price, here 300-400 rubles per can). At the end of the aust began. from front wheels. Knowing easily. It is more inappropriate to lift the arch (there is no Karcher, so use handles). Until it dries, dry the undercoat, defrost it with white spirit and cover it with vibration.

On the side of the doors, using a vibro, we sealed the gap between the fender and the body (more for the acoustic effect), and generously “flooded” everything with a cordon. After putting the fender on the place (with the first suffering) and also the cordon + barrier.

shvidshe, just mitya more))). The brightness of the rear arches was pleasantly felt.

for 4 years of complete driving without any skidding, moreover, Irzhi. Afterwards it looks like it’s from a conveyor belt.

metal!

Now, who wants to earn this kind of “decorating”: 1.Robot is SO rude. a special protection is installed wheel arches. This allows you to minimize the wasting of the saw and brood on the wing of the Renault Sandero internal sides . As a result, the machine is less susceptible to corrosion, and there is no need for frequent cleaning of critically accessible areas.

The stench appears mainly from soft rubber plastic, which is persistent to

low temperatures

It has a high value for money.

After entering the car market, all original parts were sold daily and many car dealers had to install fender locks on Logan.

The smells are small in size and they had to be adjusted to install them.

Currently, various companies produce fender guards for Renault Sander Stepway.

Ale y stench can vimagati deyakikh dorok.

For example, installing an additional noise insulation ball.

Before installing the fenders, special polymer compounds can be applied to the body.

In addition to protecting against corrosion, this will reduce the amount of vibration that is transmitted to the wheels. Before application, the surface must be washed to remove all traces of water, then wipe thoroughly and allow it to dry so that the Renault Sandero Stepway does not remove traces of water. If nothing can be done, then under the ball of polymer the corrosion will be resolved by pouring in condensate.

The main Skoda car is designed for off-road use and operation in cold weather, if the asphalt is covered with brood and reagents.

Such an aggressive mixture is badly visible on the slimy plastic parts of the suspension and body.

Hard plastic fender guards, created for the Renault Sandero Stepway 2 2017-2019, protect against external damage and ensure proper operation of the vehicle before repair.

An additional plus from the installation of fenders is the reduction of sound insulation. In our store we sell both simple fenders and those with special sound insulation. In order to make the operation of the car more pleasant, much less sounds from the road and the flow of cars are transmitted into the cabin. The installation and nuances of this unique nitrox locker are not different from the standard one. Lockery

All lockers for Renault Sandero Stepway 2016-2018 was created specifically for this model with a technologically advanced design.