A guide to the operation of VAZ 1111. Rukh in the winter minds
The car was produced at the Volzhsky Automobile Plant and was produced at VAZ, ZMA, KAMAZ and SeAZ from 1988-2008.
The Oka car began to be dismantled in the late 1970s at the Serpukhov Automobile Plant (SeAZ) to replace the obsolete S3D motorized stroller. Then the development was transferred to AvtoVAZ, where the project from a motorized stroller was transformed into a full-fledged, albeit small, car. A very current, for its time, body design and consistent with the phenomena of cars of this class in the world, which were created at UGC AvtoVAZA by designer (also designer designer) Yuri Oleksandrovich Vereshchagin.
It should be noted that this technology is one of the few advantages, if
used car
(SRSR) was not the fruit of an out-of-the-box adaptation of a foreign analogue. The prototype of the “Oka” is the Japanese microcar Daihatsu Cuore from the 1980s, but in addition to the main concept of body design and low-tech solutions, the design of the “Oka” was actually rebuilt anew (especially the power unit and chassis). The original “Oka”, like the Daihatsu Cuore, was to be equipped with an original 3-cylinder engine, but due to its unavailability until the moment of the car’s production, the 2-cylinder engine stagnated, which is actually equipped with two balancing shafts and counters to the flywheel and pulleys.
half" of the 1.3-liter VAZ-2108 engine. A fundamentally new 3-cylinder engine was ready until the beginning of the 90s, but the crisis in Galuzia caused it to go into trouble. The first large-scale models of the new car were created in early 1982.
A 3-door, 4-month hatchback of a particularly small class with a transversely mounted engine and front-wheel drive. The release of Oka was issued in 1989 at the Volzky Automobile Plant. The engine is a two-cylinder engine with a displacement of 650 cc, in 1997 it was increased to 750 cc.
About `em.
At this time, production of Oka cars has been transferred to Kamsky automobile plant, , as well as the Serpukhiv Automobile Plant Krim base models KamAZ-11113 and SeAZ-11113, will offer options with manual caravans, suitable for people with disabilities. Even lower prices will result in exports.
This small car was disassembled at the Volzhsky Automobile Plant for “corporate” production at three factories - VAZ, KamAZ and SeAZ (in the disabled version). The Volzhsky Automobile has been allowed since 1990. Subtle rice - modest
overall dimensions front wheel drive, a two-cylinder engine with a working volume of 650 cubic centimeters (the “half” of a “high-speed” engine), a universal three-door body with rear seats that fold.
Modification 11113 appeared later push the engine 0.75 liters.
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. It’s just as fateful that the Volzhsky Automobile Plant launched the production of the Oka, now they’re starting to produce both KamAZ and SeAZ, although
power units
(more than 0.75 liters), as before, only a few vases vibrate.
Addresses:
m Moscow,
Modification 11113 appeared later push the engine 1 Nagatinsky pr-d, budinok 13 (metro station Nagatinska)
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. 9-00 22-00
Robotic hour:
Usually 9:00-23:00
Professional body repair of any complexity: (straightening of dents, removal of rips, external updating of body geometry).
- repair of internal combustion engines, chassis;
m Moscow,
Modification 11113 appeared later push the engine - farbuvannya;
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. 10.00-19.00
- slipway robots; - Technical maintenance; cars, - repair of mufflers, - repair and refilling of air conditioners.
Spare parts for Chevrolet Aveo, Chevrolet Lanos, Chevrolet are constantly available.
Views: 248
m Moscow, Modification 11113 appeared later push the engine Comprehensive service for your car
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. 8.00-22.00
Rostokinsky proezd booths 3 booths 5 (metro station VDNG) We are engaged in everything related to Mitsubishi cars
.
Here you can find new spare parts for this generator.
Modification 11113 appeared later push the engine Whatever the repair, whatever the complexity.
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. Our company operates in low-cost repairs of Japanese-made vehicles of any type.
Type of repair: plumbing repairs. Mufflers and catalytic converters: installation, replacement, repair Ask for service
Pivdennoportova budinok 15 budova 23 (metro station Kozhukhivska)
Here you can find new spare parts for this generator.
Modification 11113 appeared later push the engine Szczodenno from 10.00 to 19.00
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. Direct flow-Service specialized station under repair
vibration systems cars. A team of professionals assembles robots of any complexity for repairs, replacement of mufflers, catalysts, corrugations.
Install the lambda probe emulator (sensor fake).
Prepare a direct-flow exhaust system.
m Moscow, Modification 11113 appeared later push the engine Station...
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. Woodworking repair and technical maintenance
Kantemirivsky Budinok 59 A (metro station Kolomenska) no days off from 09:00 to 21:00. LLC "Technical Center Maximum" provides technical services, diagnostics and all types of work including repair of the engine, chassis and electrical parts of the car, as well as installation
additional possession
And folding body repair is consistent with the technology of the manufacturer.
m Moscow,
Modification 11113 appeared later push the engine Repair and service area "...
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. Types of stories: 51
Visible 97-100% damage to the body vul. Bulatnikovska Budinok 2a (metro station Prazka) h 9-00 Removal of dents without prefabrication The main focus of the company's activity is the repair of dents on the car body without prefabrication. PDR technologies
(Paintless Dent Repair).
The technology allows 97-100% of damage to be removed from the car body, without the need to change and/or prepare elements.
m Moscow,
Modification 11113 appeared later push the engine Types of news: 2,372
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. Our specialty is robots with a transmission
Ogorodny proezd d4 (metro station Timiryazivska) from 10-00 to 21-00, BMW, Toyota, Nissan, Renault, Volvo, Opel and other brands.
Our company has been repairing cars for over 8 years.
All work is carried out by highly qualified specialists using wired light generators.
...
m Moscow,
Modification 11113 appeared later push the engine Technical center "SEKservice"
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. Types of news: 1,176
SEK Service can remove any folding robots
Prospekt Miru Budinok 186 (metro station VDNG)
10-00 to 20-00
m Moscow,Modification 11113 appeared later push the engine Repair of kerma laths, pumps Gur.
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. Our company has been operating a car service center in Galusia since 1992.
It provides a wide range of services for engine repair, car cleaning, car repair, injector flushing and other car maintenance services.
The flow of services to our car service center can be endless.
TRIAAA
m Moscow,
Modification 11113 appeared later push the engine Types: 8
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. 10-20
Great Volokolomsky Proezd Budynok 10 (metro station Shchukinska) 10.00 to 21.00 straightening without prefabrication using current technologies tuning, atelier, any non-standard solutions, as well as body molar robots, bumper repair, no matter how complex, local fabrication, body polishing
Types of news: 1,142
Cost-free repair according to OSACV!
vul.
m Moscow,
Modification 11113 appeared later push the engine Robocha 84, building 4 (metro station Ploshcha Illicha)
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. 9-22
Our company has been operating in the auto services market for over 15 years. We are professionally engaged in body repair, fabrication and mechanical repairs
passenger and commercial vehicles.
We also do: - servicing corporate clients.
- replacement of the windshield.
m Moscow,
Modification 11113 appeared later push the engine - Non-standard solutions...
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. Car service "Dils-Auto"
Messages: 728
We offer carpentry and body repairs for cars of any complexity!
Dobrolyubova booth 1 (metro station Petrovsko-Rozumovska)
In the Butirsky district, AutoTechCenter “DILS AUTO” is pleased to demonstrate to you its services in the quick and accurate repair of your car.
m Moscow,
Modification 11113 appeared later push the engine We will be happy to inform you
In addition, an electric car has been built on the Oka base, which is assembled piecemeal in the Dosledno-Promislovoye Virobnitsya. 9:00-22:00
Our service station is completely satisfied with the criteria that apply to dealer stations, equipped with the latest diagnostic and repair equipment and everything a necessary tool.
Customers of the auto repair center can purchase insurance for the full range of repair and maintenance services for all models.
Types of news: 8,477
Sidorov R.Yu.
On the streaming site we have posted a manual for the repair and operation of the VAZ 1111 Oka for downloading.
- For every expert who has studied this technical library, you will find information on the most current nutritional needs for car repair, warehousing, maintenance and disassembly operations.
This section contains instructions for operating the Eye, which describes the correct methods of operating the car.
VAZ-1111/1113 OKA Operation and technical maintenance in photographs
Operation of Oka vehicles This little thing was created at the Volzhsky Automobile Plant for full production from factories - VAZ, KamAZ and SeAZ (disabled version). The series dates back to 1988. Head mounted rice - even small overall dimensions, front-wheel drive, engine with two cylinders, volume 650 cc. marvel, it’s like half the engine of the “Vosimka”, a three-door body with folding seats at the back.
The popularity of this car cannot be equaled.
IT IS RECOMMENDED TO USE Unleavened Gasoline On HENDE vehicles, it is necessary to use unleaded gasoline with an octane number of 91 RON (after the previous method, “Normal”) or higher.
The production of ethyl gasoline is carried out before the release of the catalytic converter for exhaust gases (EG) and before the release of the emission control systems.
This can also be... For greater convenience, all the locks of your car can be opened with one key. However, the door fragments can be locked without using a key; it is recommended to carry a spare key with you, just in case you accidentally lock the key in the middle of the vehicle.
Keys that control all car locks Key number So that third parties cannot recognize your key number, this number...
The immobilizer is designed to reduce the risk of your car being stolen to a minimum.
OPERATIONS FOR ROBOTIC EMERGENCY MODE control lamp The immobilizer flashes for 5 seconds after turning the key to the “ON” position, which indicates that the engine immobilizer system is faulty.
In advance, adjust the seat as quickly as possible on an undamaged car.
Failure to follow these rules may result in loss of control of the vehicle and road use, which may result in damage to the vehicle, serious injury or death.
Adjusting the back seat position of the front seat To move the seat to the back position,... In order to raise or lower the doors, wrap the door handle or against the directional arrow.
Directions for wrapping the handle of the slopper for raising or lowering the stack ELECTRIC DROPPERS Electric sloppers operate only if the key to the fire lock is in the ON position.
Head pumps for sloping...
Qia system
The operation of the locks of the passenger doors and the locks of the driver's doors is in effect.
When the driver door locks are locked, the passenger door locks are automatically locked.
Attaching the seat belt To attach the seat belt, pull it out of the retractor mechanism and insert the belt bar (tab) into the lock until it clicks.
Seat Belt Buckle Fastening The seat belt automatically selects the required tension only after you manually adjust the waist belt so that it fits snugly around your waist. P... To fasten the seat belt to the fasteners at two points, insert the tongue of the buckle into the lock.
When locking the lock, there is a characteristic clicking sound.
Reverse the fastening of the seat belt buckle so that the seat belt is not twisted. Fastening the seat belt buckle with fastenings at two points (central seat belt rear seat
) Regulate... When transporting children in cars, always place them in the back seat and secure them in order to minimize the risk of injury from road traffic conditions, sharp handling or turning. Road traffic statistics show that children in a car seat experience less safety in the back seat and less in the front seat. D...і A car equipped with an additional system passive security
(airbags) SRS. The presence of this system can be seen by the presence of the “SRS AIR BAG” inscription on the airbag in the steering wheel, which is located on the center panel, and on the panel trim on the side of the front passenger above the voice box. The SRS system consists of airbags installed under the pads.
Accessory panel 1 – side deflector of the ventilation system;
2 – remixer for headlight range control;
The odometer shows the total distance traveled by the vehicle and is also useful for monitoring periodic maintenance intervals.
...
1.22 Mileage healer
The mileage meter shows the mileage covered during the trip and the last period. To reset the doctor's readings, press the reset button....
The tachometer shows the rotation frequency
collapsible shaft
engine in revolutions per hvilina (pro/xv).
The tachometer can help you select the economical driving mode, and also predicts those when the rotation frequency of the engine shaft exceeds the maximum permissible value.
Removing the hazard warning light system The flashing signal is activated as a warning for other vehicles to be careful when approaching, overtaking or passing a vehicle.
The track system should be used when absolutely necessary, or if the car has stalled near the edge of the road.
Press vimikach from any relevant vimikach. Removing the button for turning on the heated rear window Heating is used to remove frost, fogging and frost from the rear window in the middle and around the car. To increase heating, the heating must be turned down.
The heater will warm up when the rear heater button is pressed.
The rear window heater will turn off automatically after 15 minutes or when turned on. Turn it on
fog lights
, press on vimikach.
The front fog lights can only be turned down if the headlamp switch is in one or the other position.
Cup holder On the front head console there is a removable cup holder for washing bottles and drinking at the open doors.
To speed up with him, pull him by the top rope.
If the cup holder does not adjust, place it in the outer position.
Do not place third-party items on the pad.
Such items may be thrown into the vehicle interior and may be...
REMOVING THE BLENDER PROCEDURE 1. Pull the handle of the sunshade at the front part, then lower the rear part of the sunshade. 2. After this you can easily remove the sun blind. Installation of sun blinds ORDER OF WYCONANNY... The hatch can be opened and closed manually. VIKONANNA PROCEDURE 1. Pull the handle down and then forward and up, as shown by the arrows on the baby.
2. Press the center of the handle to secure the hatch in the open position.
To fold the outside rear view mirrors, press them against the rear of the car.
Directly pressed for folding the outside rear view mirror The outside rear view mirrors can be pressed against the folding of the car doors when parking in high places.
... The car is equipped with an internal rear view mirror. To select the “low” position (anti-glare), pull the tab at the bottom of the mirror towards you.
Whose situation changes the blindness of the headlights of cars driving behind you at night.
Rotating the remixer day/night of the interior rear view mirror.
Listen up first galmo parking before you take away your car.
The rear doors or trunk lid may be opened due to pressure on the rear door lock actuator or trunk lid, after which they must be lifted by hand.
To close the rear doors or trunk lid, lower them down and then push them down until they lock into place.
To ensure that the rear doors or trunk lid are properly secured, try lifting them again.
...
The filler cap of the fuel tank can be opened from the middle of the car by pulling upwards to the drive to open the filler cap of the fuel tank, which is located on the underside in the front left part of the car. Rotating is important for remotely opening the filler cap of the ignition tank. It is impossible to open the filler cap of the ignition tank. To open the hood lock, pull the hood lock drive handle.
Directly retract the handle to the hood lock drive. By pressing on the supporting part, lift the hood.
The panel of the heating and ventilation system is shown on a small scale.
Panel of the heating and ventilation system: 1 – switch of fan operating modes; 2 – knob for selecting the ventilation mode; 3 – knob for adjusting the room temperature;
4 – remix the selection of the air intake mode.
CHANGE OF ROBOT FAN MODES Change of meanings for turning on the fan.
Cleaner of waste in the vaporizer in front of the voice box and purposes for removing pollutants from the car interior and for cleaning the surface.
Rotating cleaning of the air for the evaporator and fan Forward Replace the skin filter 20,000 km or once per river. When operating a vehicle with heavy road minds
, more frequent inspection and replacement is required.
How a car stereo system works Signals in the AM and FM bands are transmitted through repeaters located around the location. The signals coming from them are received by the car's antenna. It is important to change gears at position “N” (“Neutral gear”) and release the accelerator pedal.
On a car with an automatic transmission, set the selector lever to position "P" ("Parking"). First of all, get over it, what... The position of the important alternation is traditional for five forward gears, as shown on the baby.
Positions of the importance of shifting gears Increased transmission
reversing
, after moving the car again, be sure to change gears for at least 3 seconds at the neutral position.
After this, it is important to move the rear gear position.
Positions are important for alternating modes with an automatic transmission. The highly efficient HENDE automatic transmission has two gears for forward driving and one reverse gear. There is the original gear re-mixing circuit, shown in figure 117. At the beginning of the day, in the first position of the rich-functional re-mixer on the gear re-mixing circuit is on. 1.64 Anti-block system galm
PRACTICE THE CORRECT HALMANSHIP Before starting to park after parking, make sure that the parking lamp is turned off and that the galvanic system warning lamp does not light up.
After driving through water or driving a car, the galma may get wet.
Wet debris is no longer safe, and fragments of the car can become harsh.
To dry the galms, lightly press the car on them for an hour. 1.65 Economic water By following these instructions, you can save heat and increase the mileage of your car without refueling: – drive smoothly and avoid sudden accelerations. Try to collapse with steady speed and don’t get angry in front of the gap;– try to save money
traffic flow
Advance Consider towing a trailer for the first 2,000 km to ensure that the parts of the new vehicle are received.
Failure to complete this approach can lead to serious damage to the engine or gearbox.
Towing hooks Select the correct combination of towing device, changing the connection so that its loosening is avoided with the fastening place. 1.69 Engine does not start If the engine is not checked by the starter or is already fully checked if the car has an automatic transmission, move the selector to the “P” or “N” position and turn up the emergency warning lamp.
Reverse the connections between the wires and terminals
rechargeable battery
, so that the stench is clean and strong.
Turn down the interior lighting lamp.
Like a lamp burning from...
VIKONANNYA PROCEDURE 1. Turn over the fire at the tank. 2. Check the connections of all the wires of the ignition system, the coil and the ignition spark plugs. Please reconnect or the connection is bad.
Connecting the wires of the ignition system, the coils and the ignition spark plug 3. If you smell the smell of gasoline, you may have become overloaded with the ignition mixture ("...
Advance Before towing, turn the vehicle over to automatic transmission transmission
If it is below the "HOT" ("Hot") symbol on the dipstick, add more water.
If you cannot fill the water, you need to use a wagon for towing.
In case of emergency towing, if it is not possible to quickly respond to the services of a tow truck, secure the towing rope.
1.76 Corrosion control and periodic inspection
Protecting your car from corrosion Using the latest technologies and methods of protecting your car from corrosion, HENDE protects high-corrosion cars.
Primary causes of corrosion The primary causes of corrosion on your car are: – road mud, dirt and water.