Repair of overall lights VAZ 2115. Why do not burn overall lights

Overall lights - lamps, giving to understand another car about your dimensions. For example, stopping at the roadside on the track, turning off the ignition, the neighbor goes out, and the dimensions remain. Yes, and in rules of traffic rulesFor information, the parking lot on the sidelines is allowed only with the included dimensions.

In this article, we will consider the main reasons why dimensions are not burning on VAZ 2114. This article will suit all SAMAR owners, both the first generation and the latter.

Blocked lamp

Blocked fuse

But if you simultaneously refused 2 dimensions, then Bishm front and rear left, and even backlight the number, then the problem lies in the mounting block. Namely in the fuse F10, which is responsible for the left dimensions, the interior lighting, the backlight of the number, the backlight of the panel. But keep in mind that the F10 fuse responds directly for the left dimensions, if you do not work other, then seek the corresponding fuse in the article.

Contacts oxidized

We analyze the fuse block, namely the pads of all tires to the fuse block and relay. Most often they are sewn, disconnected, poorly in contact. Clean the contacts, connect well. Do not forget pro contact group On the headlight block, it may have oxidized there too.

The inclusion button does not work

The fact is that it was possible to break the switch (button) of the overall lights. The problem is typical: the wire has deployed or oxidized. We clean, fix the wire and check.

The fuse is burning

If the fuse is constantly burning, then two options are possible:

• bad contact in the fuse block;
• somewhere is korotitis (closed).

Check:

• We take a light bulb at 12 volts and connect two wires to it, respectively, + and on -.
• We take out the blurring fuse and connect the wires from the light bulb to the places of its contacts. If the lamp is burning, then somewhere closure.

The only way to find the location of the closure, disable in order and check the same way everything is responsible for which the fuse.

Main diseases is:

1. Wires that go to the trunk lid and on the backlight number. Most often, they are swiss and closed.
2. Following weakness, because of what they do not burn on the VAZ 2109, then the trap the loop, which is from the driver's left foot, which is not on the engine shield, and on the back of the wing side, under the carpet. Disconnecting the loop, Matt Just disconnect the circuit to the backlight number and the lighting laying.
3. If after that our lamp on the fuse block will go out, then we found a place where it closes. Next you need to fully watch the wiring and treat the tape.

When driving a passenger car VAZ-2115, regardless of time, parking lights, as well as light headlights, must be included. This is the prescription of Russian rules roadwhich is obliged to perform every driver. Therefore, electrical circuits The overall lights and stop signals, work through the control relay of the K4 lamps, in the task of which includes a driver alert with the help of light and sound signal On not the inclusion of at least one of the lamps above the listed electrical circuits. It will make the driver get out of the car and determine which lamp of the overall light does not burn, and search for a fault that has arisen.

The VAZ-2115 car more often stops the lamps of overall lights in the rear lights. It is connected with the occurrence of not the tightness of the lanterns, as a result of which moisture falls inside, which leads to the oxidation of the plug of the pad or track on a flexible board, through which the voltage to contact the lamp is supplied.

There are cases when after translating the outdoor lighting switch to the first position, no lamp of the overall lights light up. The search for such a malfunction will have to start with checking the presence of voltage on terminal 1 of this switch. It should be equal to +12 volts, even with the ignition turned off.

If this terminal is de-energized, then it will be necessary to sequentially check the voltage on the terminal 6 of the X8 connector, and then on terminal 6 of the X1 connector mounting block. If there are voltage terminals on these terminals, the culprit of the lack of power on the terminal 1 of the outdoor lighting switch will be a pink wire connecting it from the terminal 6 of the X1 connector of the mounting unit.

Well, if there is a voltage on the terminal 1 of the outdoor light switch, the culprit of the non-enabled lamps of the overall lights can be the switch or control relay K4. To make sure that the switch has failed, you need to translate it into the first position on and check the availability of voltage on its terminal 2. If there are no voltages on this terminal, the outdoor lighting switch will have to be replaced.

When the fuse fuse F10 (7.5 A) will not be lit the front and rear lamps of overall lights on the left side of the VAZ-2115 car, and when the fuse F11 (7.5 A) fails, both lamps of dimensions on the right side of this car. Freamer F10 Fuse can be defined instantly, without even looking into the mounting unit, since the lamps of the switches, heater control levers, cigarette lighter, ashtray, because it protects these electrical chains.

When moving in the dark or in the fog, the overall lights are indispensable, especially if they are behind. When moving or during parking, they show other motorists, where your transport is located. If the rear dimensions are not burning on the VAZ-2114 car, it will be easy to make repair with your own hands. To do this, it suffices to find out the reason and stick to the instructions below, or view the video.

Characteristics of overall lights VAZ-2114

VAZ-2114 refers to the modification of the "Samara" of the second generation. Overall lights in them are located, in accordance with technical Regulations, The edge of the front and back of the body, next to the turn signals. These lamps include headlights.

1. Unlike the front overall lights, the rear is painted in red.
2. The inclusion button of these headlamp is in the outdoor lighting control unit. It is located in the center dashboard over on-board computer. If the dimensions are enabled, the green light lights up on the switch.

In the engine compartment under the hood of the car there is a mounting block with fuses. If you do not work lights only on the left or right side, then, most likely, one of the fuses failed. Most easily notice the fault of the F10 element, as it responds not only for the work of the right side of the overall lights, but also for fulfilling his duties control lamp.

If the lanterns refused to work on the left side, the fuse F11 is subject to replacement.

Why may not burn the rear envelope

None of motorists are insured against faulty overall lights. It is important to quickly understand what is the reason, and carry out repairs. One of the lamps often fails, then you can assume the reason for failure:

• she burned out;
• bad contact;
• truck in the wiring leading to this lamp.

The first is most often found, in this case it suffices to replace the lamp failed. If the lamp works only if you knock on it, then problems with the contacts (although the physical impact does not always help). If during testing you found that the light bulb is a whole, and oxidation or carbon in the cartridge is not observed, then you need to check the conductors.

Replacing a spoiled lamp in the rear unit of the headlights is carried out according to the instructions:

• disable the lighting and open the trunk;
• remove the decorative upholstery;
• squeeze the locks and pull the Lantern Contact Panel;
• click on the burned lamp and turn it counterclockwise;
• check the light bulb on the tester and, if necessary, install a new one.

Lantern assembly is carried out in reverse order. Replace the flashlight and assemble. For this, it is important only to purchase a qualitative option that is not different from the original. Car enthusiasts are often recommended to acquire stock components or pay attention to Oryvo. We recommend replacing assembly if there are significant design damage.

Often the lamps of the rear dimensions do not immediately burn out or refuse to work, but they are negated by a weak glow. To begin with, clean the contact group located in the mounting block, and then, if the fault failed to fix, believe the groups leading to each lamp.

Which is especially important to control the rear dimensions

If the control light is lit on the key, but the dimensions work, then first browse the panel wiring. Remove the keys block from the socket, then wipe the contacts with alcohol. If simultaneously with the control lamp, dimensions do not work on the right side, then check the fuse. It is worth noting that they are out of order extremely rare, as in the VAZ-2114 began to establish broad options that have a reliable contact pad.

If F10 or F11 is still often breaking, it is necessary to check the mounting unit, it may be faulty. If this node is in working condition, then check the entire electrical circuit. Sometimes the constant breakdowns of fuses indicate a closure in the wiring, which can lead to a fire without visible reasons.