How to Choke Tempered Glass for phone. How to stick a protective glass on the phone

All pictures are clichable

In the review of the glass scrolidate, I promised a couple of months to tell about the experience of exploiting this accessory. It is interesting primarily against the background of problems with the preceding generation. Could the company be able to defeat the problem with the edges that are dugs with time? Not really. Read more about it below.

Oh good

Before starting to "kick the glass with legs," I would like to tell about the positive points of its use. In particular, by the convenience of operation, no plastic or polyurethane film is still unable to compare with a full glass. There is absolutely no effect on the image, plus the finger slides over the surface of the glas.tr as well as on the iPhone screen.

On the phone, the accessory "checked" more than three months and, of course, at this time I was not particularly worried about the preservation of the display, I wipe it on something, sometimes put the glass down, in general, did not strain. All the same, the scriprotector is glued, and it was necessary to test it well. So did not scratch, although not hard and tried. Naturally, if desired, you can soak anything, but in hardness Glas.tr do not have to doubt - a complete analogue of that glass, which is worth it.

In addition, even during the writing of the review, I conducted an experiment with a glass crossing, as the first time it fell curved. As a result, a pair of small bubbles with the edge was formed, in the lower right. It was afraid that they would quickly grow up to decent spots, but this did not happen, and the size of the bubbles was left for 3.5 months the same:

About features

A slightly enlarged weight of the gadget, I personally did not feel, but every active user of the iPhone 5, who took my phone to hand, noted that he is heavier than usual. It is worth considering it. Although the weight gain is meager - up to 10 grams.

It is more important that the fact that not with all covers is compatible this glass, as 0.5 mm increases the thickness of the phone. For example, in the Panch, the device with a glass screenshotctor is placed, but it enters and removed with a certain effort. Spigen SGP Argos flip covers are not very tightly closed, all the same extra 0.5 mm make themselves felt.

In addition, the effect almost disappears when the picture seems to soar above the screen. This is a trifle, yes, but when I reached the glass, then with a special force I felt the entire buzz from the display, made using full lamination technology. That is, without an air layer between the layers, plus the touch panel is built directly in safety glass.

Bubble again

Actually, it was the most burning moment of the experiment. Will the glass begins to dig up at the edges, how did it happen in the case of the first generation on the personal iPad and on the Galaxy Note Comrade? I will not pull a cat for a causal place and answer immediately - yes, a juicy bubble appeared in the corner:

And he got sharply and literally in two times in two times. Thus, the glass lasted a little more than three months, but it is worth considering two points. First - Manufacturer on the screenshot packaging prevents that it is desirable to use it simultaneously with a bumper type case or with an analog that covers the edges of the glass. I did not bother with such a thing and the iPhone 5 for the most part was the goal as a falcon.

Second moment - On debt of the service, you have to constantly break the smartphone in a different kind of accessories, and there are times when the gadget is decently squeezed, twisted, etc. This also gives its negative effect on the glass screenshotctor.

For clarity, he recorded the video and in it, in addition to the demonstration of Glas.tr flaws, the process of the brutal dutching of the accessory is demonstrated:

In the dry residue

What to say here? Screen proder dear, it is advisable to use it together with a bumper, plus the weight and thickness of the iPhone 5. On the other hand, the full alternative to this kind of glass has not yet been invented, and on tactile sensations it remains a standard.

It should also be noted that in Spigen SGP are now working on the third generation of such accessories, the main difference of which is in a reduced twice thickness. Theoretically, it will solve both the problem of compatibility with covers and with a gradual sprouting of the screenshotector. As soon as the new Glas.tr falls into the hands, I will definitely write about it.

Wow, new Apple:

Being constantly in operation, mobile phones are subjected to various mechanical impacts, which sometimes are able to deal with the device. Sometimes one careless movement can cause the purchase of a new gadget. So that this does not happen, you need to glue the protective glass to the phone. It will provide the screen with moisture, dust and minor shocks.

Necessary materials and tools

It is advisable to glue a protective glass on a smartphone or another mobile device Immediately after buying, not to experience fate once again. It is necessary to understand that the screen is a fairly sensitive part of the phone, and strong scratches are capable of not just spoiling the appearance, but also to cause serious breakdown. And even ordinary keys can damage the display if they are in one pocket with the device.

The procedure for replacing the protective glass is similar to installing a new one. To glue it, the following materials and tools will be required:

dry rag;
napkin impregnated with alcohol;
liquid intended for cleaning screens of computers, televisions or mobile devices;
scotch;
new protective glass.

Step-by-step instructions for gluing protective glass on a smartphone

Before you understand how to glue the protective glass to the phone, you need to buy it. To do right choice, Certain nuances should be known and adhere to several recommendations:

Glossy protective glass is cheaper than matte, but ensures the protection of the phone screen from shocks, moisture and pollution.
Matte protective glass, though more expensive, but protects the screen of the phone not only from shocks, moisture and pollution, but also from glare.
Before purchasing a protective glass on the smartphone screen or other mobile device, it is necessary to test it for strength - it should not be bad.
A oleophobic coating is indicated about the high quality of the protective glass on the phone screen.
It is recommended to give preference protective glasses For the phone screen, included with special napkins or spare films.
Thicker protective glass will provide better defense For the phone screen.

On a note! It is important to prepare a workplace in advance. It is better to choose a room that contains a minimum of dust. For example, an ideal place to stick a protective glass on the smartphone screen, is a bathroom or kitchen. In the living room and bedroom there is enough textile that attracts dust particles. As a result, trouble may occur, interfering to glue protective glass on the phone screen. Work table is better won with a napkin.

Step-by-step instructions for gluing protective glass on a smartphone:

Before sticking a new protective glass or a film, you must remove the old protection. For this, it should be slightly pulled at its edge at an angle of about 60 degrees.

Before starting to glue the protective film or glass on the smartphone screen, you must thoroughly wash your hands using soap. In addition, the phone display surface must also be clean and smooth. Using an alcoholic napkin, you need to get rid of contamination. You can also apply a cloth moistened in the cleaner to clean the phone screen. Means for removing contaminants can be made independently, mixing water and alcohol in a ratio of 5: 1, respectively and adding a small amount of gel for washing dishes. The working surface also needs to be cleaned.

The screen of the phone must be carefully wiped with a napkin to shine. In the event that dust particles remain, you should walk with scotch, as you can see in the photo.

Protective glass is required to get out of the package and remove the film from it. Protection is installed on the screen so that matching with the central button and phone speakers. To secure the protective glass on the surface of the smartphone display, it is necessary to spend your finger in the center from top to bottom.

If air bubbles remain under protective glass, they will have to get rid of them. To do this, hold a credit card or a spatula, which comes with the center to the edges.

It is not necessary to provide strong pressure on the display, air bubbles will quickly be removed even at easy pressing. If it turns out a smooth and smooth surface, the protective glass managed to glue correctly. Despite the small thickness, at the expense of which many equates this lining to the film, it provides reliable displays from external influences.

How to re-glue a protective glass?

Many owners of smartphones and other mobile devices are asked: Is it possible to re-glue the protective glass on the display? Modern surfaces of gadgets are allowed to reuse. To stick protection again, you will need to carefully remove the glass, and then wipe the adhesive side with alcohol and give to dry. After that, you can glue protection, without forgetting about the coincidence with the button and speakers. Next, only drive bubbles with air will remain.

Video: How to glue the protective glass yourself on the phone?

The video presented below will help properly glue the protective glass on the phone screen at home. As a result, the device will ensure reliable protection against scratches, the destructive impact of moisture and pollution, which will extend its service life.

The phone is a fairly expensive thing that accompanies us every day. At the same time, it is very much like to save his original appearance as long as possible, save from various damage. Most weakness Smartphone is a screen. Despite modern technology, the display continues to collect numerous scratches that negatively affect its appearance. The only reliable way to protect the display from scratches is to stick a protective glass. But this is not so easy to do. To serve for a long time and reliably protected the screen, you need to clearly know how to stick it on the phone.

Of course, employees of cellular salons will kindly offer their services. But for this it will be necessary to pay a considerable amount. Therefore, it is better to stick the glass yourself. In addition to saved money, you can get a good experience. In addition, it will make it better, since the shopping staff has enough sufficient time to comply with the entire process technology.

Benefits of glass before film

The film is much cheaper, but it has a number of shortcomings. Firstly, it flashes faster and fades. Secondly, the film does not protect against chips when shuffles. These parameters are enough to purchase glass and securely protect the device.

The following parameters include the actual advantages of glass:

it is almost impossible to scratch;
for a long time, it looks like a new one, will not fuss, not rubbing;
reliably protects not only from insignificant damage, but also from severe mechanical impact;
it is securely attached to the display, due to silicone basis.

In addition to the listed advantages, there are some shortcomings:

increases the thickness of the phone;
it has a high cost compared to alternative protection methods.

Given that the shortcomings are not critical, the glass always remains the most aesthetic and practical way to protect the screen.

Characteristics of protective glass

At first glance, such protection is a monolithic part, but this is an erroneous opinion. In fact, it consists of five layers. In this case, its thickness does not exceed 0.3 millimeters.

The first layer is a oleophobic coating. Thanks to him, the finger with ease slides across the screen, and the pollution is removed without much effort. The second layer is protective. It is he who constitutes a solid foundation that protects against mechanical damage. The third layer protects from glare. The fourth restrains fragments, not allowing them to fly away in case of damage to the glass. The last layer consists of silicone, due to which it is securely attached to the surface of the display.

Protection glass gluing technology

Before sticking the protective glass to the phone, you must prepare all the necessary inventory. The minimum set of tools consists of an alcohol napkin and a pure lint-free cloth. Also, you need to not forget to wash your hands and preferably wipe with alcohol. This is done in order not to leave the stains on the screen and protective glass. Otherwise, you will have to spend the mass of time to remove contaminants.

Glass sticking is carried out in several stages:

If everything is done correctly, the procedure can be considered completed and enjoy the result obtained.

If the phone is completely new or recently purchased and the factory film has been preserved on it, then it is expensive to degrease and wipe the display. The factory film reliably protects the screen from dust and fat. It is enough to remove it and immediately stick the glass.
If the first time failed to stick exactly, you can try again. To do this, it is necessary to completely carefully disable the edge of the glass and remove it from the screen. After that, repeat the procedure according to the instructions. The main thing is to remember that attempts are a bit, since after each dug, the silicone basis is damaged.
If dust got between the film and the screen, you need to carefully rejuvenate the glass, remove the contamination, then repeat the sticking procedure.
If the phone has previously damaged or completely broken protective glass, then it can be removed using any plastic card. This method is the most efficient and safe.

At first glance, the process may seem complex and time consuming. In fact, the whole procedure will take no more than ten minutes. The main thing is not to be afraid. Taking advantage of tips from the article, you can safely protect your smartphone and get a good experience. The main thing is to believe in your strength and remember that no man sticking protective glasses ended the specialized institute in this area.