Film against fading glass. Solving the problem of fogging automotive glasses

The motorist must remember that the main thing is to ensure safety on the road both for himself and for pedestrians. In winter, fogging windows in the car makes this question even more relevant. This problem has its own prerequisites and solutions. About why this happens, will be discussed below.

Possible reasons

Car windows sweat, firstly, due to the temperature difference in the cabin and outside. The temperature in the car is slightly higher than on the street, therefore condensate is formed. If you have a question about how to deal with the fogging of glass in the car, then there is a simple solution. Sometimes it is enough to make the atmosphere in the car more dry and only to heat the glass.

The damaged ventilation system can also be the cause, because of which they sweat. Sometimes system valves can be closed as a result of repairing the machine or due to excess salon vestivity. It is also possible that moisture from the drain openings of the cooling system will fall into the interior of the car. To correct these malfunctions, you need to read the auto operating manual and explore the ventilation system.

Video about a simple solution to this problem:

It also happens that the fluid penetrates into the salon due to the non-working engine cooling system. But this problem will be difficult to solve and better go to the service.

Oddly enough, but the answer to the question "why the glasses sweat in the car" lies in your passengers. This is another cause of condensation or fogging. The air that we exhale is considered very wet. Therefore, passengers should refrain from unnecessary conversations at least for a period of time. Your satellites can consume alcohol before traveling, which will create additional problems for glass. In this case, it is best to abandon the planned trip on your own car.

Solution to the problem

• Why is it important to cope in time with moisture inside the cabin of your car? It can get inside, for example, because of the old seal. In winter, it may be snow in the car, and at another time of the year - droplets of rain. When the temperature in the cabin rises, this moisture will evaporate, and then condensed. Therefore, car windows sweat. In the fight against moisture, you can use the salt packaged in a paper pack, which will lie on rear seat car. Try to clean the mats from excess moisture or use some paper that you can put under your feet. Remember that in the cabin should not leave raw rags.
• To protect yourself from fogging, it is enough to keep the interior of your car closed. But if you open the door, the moisture will again be collected, worsening the purity of the glasses. In the cabin, it's not so easy to return the climate, why and it is necessary to check its tightness.

• At the first signs of fog, it is necessary using deflectors to change the flow of air flow by sending it to the glass itself. Thus, we will achieve changes in the circulation of air masses inside the car and carry out the heated of the glass. If you have air conditioning, then with it, you can quickly solve this problem. It is worth remembering that during the operation of the air conditioner should not use the internal circulation. Sometimes, because of the dampness on the street with its functions, the filter does not cope, as he just does not have time to dry. Very often, this issue is solved by the usual replacement. The filter requires verification and in the event of problems with the glass heating system.
• In the car windows, the glass sweat is not the first day, so many people have long been known for all sorts of ways that are directed against this problem. Car owners use a simple recipe: mix one share of glycerol with ten alcohol shares. Then rub the windows. Glycerin in pure form does not have such actions, because it can leave behind the trail, which in the dark will worsen visibility. Willing with glasses by newspapers is one of the oldest techniques. At the same time, paint with newspapers also leaves a film, as after the use of various chemical automotive substances. You can also clean the glass with a cigarette tobacco.

• But why not solve this task using the diversity of proposals in the market? Today you can find many products for servicing your car. One of the most sought-after is a means that helps to protect against fogging and directed against the formation of condensate. It is represented in the form of sprayers, various liquids and napkins for glass. This substance forms a small film, which prevents moisture to settle on the surface. The moisture is simply rolled down, and the glasses remain dry. Either it happens that windows still sweat, and drops remain on the coating, but at the same time they form a transparent thin layer. You will not get the expected effect if you apply a means to a crude surface. Glasses should be clean. You can see that solving the problem of fogging, you will also get a pleasant delicious fragrance in your car.
• Also, the solution is reduced, for example, to the use of a special film for glass. It is easily applied to car windows. But it is best to entrust her installation to competent specialists. Such films are created not only against the formation of condensate, but also perfectly perform protective functions and apply not only for the car.

Video to eliminate condensate:

RESULTS

We looked at the famous problem when the glasses sweat in your car. We disassemble why this happens. It turned out that they sweat primarily due to the difference of temperatures or the appearance of moisture in the cabin. Now I encounter this problem, you can easily find a way out of the situation and you will always have clean glasses. Most importantly, listen to your beloved "Iron horse" in time.

Subscribe to our channel in Telegram. Recent and current news from the automotive world!

On the road, this is the main thing that the driver of the car should provide for themselves and pedestrians. And during the periods of changing seasons, as well as in the winter cold, this is especially true. This is due to such a phenomenon like fogging the brass in the car. It can be called a big problem, but it has its own reasons and ways to eliminate.

Also, the cause of moisture condensation is the car passengers. Much harder and more saturated with moisture. Therefore, the trip to the noisy company requires the driver of a frequent reconfiguration of the climate. However, with a situation where the technique does not cope, the passengers are better to be silent for some time.

Video about the reasons for fogging

There are cases when the problem lies in the malfunction of the ventilation system. When repaired, bits behind, ventilation valves can be taken. The problem may be in excessive cabin litter or car trunk. To solve these problems, you need to get acquainted with the instructions for the car and check the health of ventilation in the car. The drain holes of the air-conditioning system also does not interfere with check, because the liquid of them can simply be blown in the salon.

The problem may wage in the engine cooling system malfunction. In this case, the moisture will fall from there to the salon. In this case, the best solution will turn to.

Problems with passengers can be in the presence of drinking alcohol. Therefore, the optimal solution will not use the car in the case of drinking alcoholic beverages by passengers.

Methods of struggle

When the first fogging evidence appears, it is necessary to change the circulation of air in the cabin. For this, the direction of the moving air, turning to the glass, change from the deflectors, and thereby heating them. The availability of air conditioner in the car solves the problem even faster - literally in a few minutes. The main thing is that the internal air circulation in the cabin is not included. In the event of a collection of heating and drying system, you need to check the filter. Often he just does not have time to dry during a wet weather. Perhaps it will simply be replaced.

There are a lot of accessories on the market for car care products, and a means of fogging a car of a car is one of the most popular in winter time of the year. It is represented by B. various forms: Napkins, liquid and aerosols. Their action is based on changing the surface tension. The tool covers the glass of the finest, which does not allow moisture to remain on the surface. Drops are formed that roll down. Also can moisture and remain on the surface, but lie with a thin and transparent layer. The means is applied to the dry and clean surface, otherwise it will not work. In addition, a pleasant smell will create a pleasant feeling of comfort in the cabin.

Considering that the glass is fogged in cars from the very beginning of the production of transport, many have already found ways to fight this phenomenon with handicrafts. Many drivers have a simple recipe: 10 pieces of alcohol are added to 1 share of glycerin and applied to the glass. Pure glycerin is not as effective, as it leaves the bold layer, and in the evening and night time it significantly worsens visibility with highlights. One of the oldest is wiped the newspaper. Typographic paint at the same time forms a film similar special tools in the form of auto chemicals. Some wipe the glass even tobacco from cigarettes.

There is I. long-term solution - this is . It is applied in the same way as. According to its principle of action, it resembles those films that protect the helmets of motorcyclists, special optics. Of course, this is due to certain expenses - only a professional can install it.

The easiest way to fight is to save the salon closed. IN emergency situations This prevents the formation of moisture. However, at the first ventilation, the moisture will be condensed on the windows, as it will be difficult to restore the climate in the cabin.

In winter, snow can get to the salon, to other seasons and raindrops. Therefore, during the heating of the cabin, the moisture evaporates and condenses on the windows. Therefore, it is extremely important to remove it from the salon. To do this, clean the rugs from snow and raindrops, in the extreme case - put the newspapers under the legs. It is also important tightness. Very often, the sealer can spoil and "depart", because of what moisture penetrates into the salon. It is impossible to store wet rags in the cabin. Also helps and salt in a paper package in the back seat.

How to eliminate fogging glass in a car:

Thus, solving problems with fogging is very simple and implemented. It is important only attention to the operation of your car and a timely response to malfunctions in its work.

The fogging of the glasses is an aggressive factor in the process of direct driving machine. In order to deal with this problem, it is necessary to identify the primary cause of the formation of extra moisture on the surfaces and choose the most effective remedy for fogging the car.

Causes of condensate education

Why can the glasses die? That is good reasons, reasonable, mainly by conventional physical processes. Most often, condensate on the windows is going in the year when the air temperature on the street is extremely low.

The primary preceding fogging factors are:

1. Essential air temperature in the cabin and on the street. Inside the car is always warmer and wetger than in the external environment. In this regard, the extra moisture located in the cabin condenses on the cold windows. So there is a fogging.
2. Increased humidity of the plaid elements of the cabin. When the heating is enabled, an extra moisture from the rugs or passenger seats evaporates and settles on the glasses.
3. Alcohol Couples in the Air. Alcohol drunk by passengers in honor of a holiday is gradually released during the respiratory process. Alcohol couples absorb moisture from the air. Educated water drops are settled on car windows.

Video about condensate in the auto cabin:

Fighting condensate and improved visibility

So that the windows of the car remained transparent it is important to know how to deal with the fogging of the glasses. For this, a number of funds and effective modern techniques are offered.

1. Use of various modes of the built-in climate system
2. Application of specialized anti-plants
3. Casting windows film containing condensate education
4. Dried salon
5. Ventilation valve checking
6. People's methods to combat madmen
7. Reducing conversations during a trip

The best prices and conditions for the purchase of new cars

Each motorist operating the car in the autumn-winter period, is familiar with such a phenomenon like fogging glass in the car. Question: "Why do glass fog in the car?" There was approximately at the same time as the car itself. This phenomenon significantly worsens the review, which creates a prerequisite for inadequate acts of the driver. Poverty glass is the reason for many.

Riding with a stuffing glass is not very pleasant

Let's try to figure out the problem of complex. In our opinion, it consists of three components:

• Causes contributing to the process.
• Methods for effective elimination.
• Means that ensure efficient fogging.

1. Causes of fogging glass in the car

Almost every car enthusiast was asked: "Why do glass fighten in the car?". The main factor affecting this process is to increase moisture content in the air located in the car. The stamped glass of the car is the result of the condensation of moisture contained in the "exhaust" human body. In addition, in each modern car There are several other sources of high humidity: accumulated moisture noise isolation, water in pallets rugs, wet insanity of the cabin, etc. The inclusion of a fan that catches the warm air is usually ineffective, since an increase in air temperature in the car facilities contributes to an increase in the intensity of moisture evaporation, and, consequently, fogging glass.

In addition, one of the factors affecting the fact that the glass in the car is fought is to block the drain hole in the climate control system that prevents the conclusion of condensate.

So, why the glasses fog in the car, we understood. How to deal with this phenomenon?

1. Methods for eliminating the problem of "Poverty Glass"

Fighting the fogging of glasses in the car involves two methods - prevention and elimination of consequences. The first, undoubtedly priority, since it allows not only to eliminate such a phenomenon like fogging, but also to maintain functionality and performance features Car glass.

Preventive measures are in the processing of automotive glass with special substances - "antiperspirants" that prevent the formation of fogging. Means from fogging glass in the car are made in two aggregate states: aerosol and liquid. The main problem affecting the choice of funds that prevent fogging glass in the car is a combination of two factors: the level of their quality and compliance with the motorist of the rules of their application. Application of low-quality drugs on glass windows leads to the formation of stains and divorce glasses on the treated surfaces, creating significant difficulties in maneuvering in complex meteo conditions and in the dark.

Now that it is to take when the glass swamped is a faithful fact. We offer several effective practical advice:

• In the process of warmling the car, all available devices must participate: rear window heating, heating system, blowing, air conditioning, recycling;
• The process of effective salon warm-up assumes the complete absence in it (cabin) of passengers;
• Periodically dry the noise protection and rugs;
• Watch out for the state of the filter absorbing excess moisture;
• Carry out the salon at the end of each trip.

1. Means from fogging car windows

Let's start with the so-called "folk" means of combating this phenomenon.

There are still quite a lot of car enthusiasts, confident that if the windshield fades, it is necessary to contact the "Dedovsky" method - rubbing salt. This method is the most barbaric of all now known, because it has low efficiency, damage the glass, contributes to the emergence of corrosion phenomena, etc.

One of the chemical agents that prevent fogging glass in the car is glycerin. However, it is also not ideal, since the film formed by glycerin contributes to the formation of glare, worsening the review. In addition, it is trite dirty salon and passenger clothing.

Another means of solving the problem will be modern chemical "antisoles" - fluids and sprays. Their quality depends on the manufacturer, chemical composition and compliance with the conditions of application (applying to dry and clean glass).

Modern manufacturers offer potential buyers a rather wide list of products of modern chemistry, helping to make automotive glass Clean and clear: "K2 FOX", "TRITON", "SINTEC". However, as you know, everything is known in comparison.

A variety of motorists often raises the question of why car manufacturers do not provide for the presence of janitors with inner Windshield. Such questions proceed from driving experience, especially in winter periodsWhen the windows are fisted and accounted for by rags to solve this problem. Often it is in the cold season that the problem of fogging glass arises vehicle. Of course, to great unfortunately, all the consequences of such a minor little things at first glance can become fatal. That is why it is necessary to clarify the question of why the glasses are fought in the car, and most importantly - how to deal with it?

1. Why does the car window fog?

The first thing should be referred to as moisture condensation. It is important to note that in the fogging of glass from the inside of the car, the main stimulus and key element is water and its pairs, the content of which will vary in the atmosphere due to changes weather conditions and pores of the year. If you figure it out, it is very easy to determine the reason for the fogging of the glass, as it is possible to produce an elementary experiment - you should ride on glass or mirror.

The same phenomenon is observed in the bathroom, when all the surfaces of the glass will be fisted during the periods of the shower. In fact, water drops will accumulate on all surfaces, although they can not always be noted. Condensation is the scientific name of the fogging process.

Condensation is a transition of a substance (water) into a liquid state of a gaseous state. It will happen in reality during cooling, as a result of which the result (final product) will be called condensate. The key in understanding of the entire process of fogging and the emergence of this condensate is the concept of "dew point". This ordinary temperature at which the air will succumb to the maximum effect of water (accumulation of water in the air), as a result of which condensate will be formed.

The dew point itself is directly associated with the temperature and humidity of the air: the humidity of the air is less, the stronger it will be necessary to cool it for the occurrence and formation of condensate.

As a result, we will get such a picture: in the summer and winter, the dew point will not be the same, since relative humidity will differ at different times of the year. In addition, the car grid will play the role of the site, which will be intended to distribute condensate, since it is precisely the glass that will be the boundary between the temperature modes of the internal state (in the cabin) and external (outside the window).

It is also important to note that the reasons for the fogging of glasses in winter and in summer will not be the same. Relative air humidity in summer period An order of magnitude higher than the same figure in winter. Based on this, the dew point will be achieved only at high temperatures.If the air conditioner works in cold mode, and also in circulation mode, it will maximize the release of condensate. The following picture comes out: from the outside the glass will be warm through the summer sun, and the temperature inside the cabin will be much lower, as a result of which the glass will foggle.

In the winter period of the year, everything will be directly proportionately on the contrary: inside it will be hot, and outside cold - glass will rebuild. The only difference will only be that the dew point in cold periods will be achieved at low temperatures. If the case will occur in early autumn or in the spring, when it is still cool on the street, and the air humidity increases through heavy rains, the result will remain the same - nothing will be visible as the glasses have fallen again.

2. What should I do if the glasses are fisted?

The easiest solution to the problem has been wiping the windows by means of an ordinary cloth. Although fogging and will be eliminated, after a certain period of time, it will bother the motorist again, as a result of which the need to eliminate the problem again. In addition, during the immediate movement of the vehicle, wipe the glass is quite dangerous. Nevertheless, if there is no other option, you will have to resort to this option and take a rag in the hands. It is also important to remember that the rear windows should not be wiped, since part of the moisture will condense on them, and will remain transparent an order of magnitude longer.

In order to more effectively solve the problem, the problem should be simply determine why fogging occurs. Because of this difference in the inner and external temperatures there will be condensate. Consequently, this difference must be made minimal. Of course, the easiest way is when the car is equipped with air conditioning: in special mode By blowing the windshield during cold mode will shrink the difference in temperatures, which will help to eliminate the fogging.

However, if not installed, then you can cut the temperature difference by omitting the side windows. Although, after that, the temperature in the cabin decrease significantly, as a result of which the passengers and the driver will not be sufficiently comfortable. If it happened so that the motorist could not prevent the occurrence of fogging of glasses, then they should be used by some advice, through which you can quickly get rid of it:

1. The greatest effect of condensate is directed to rear glass, as a result, it should be enabled its heating at the vehicle's institution.

2. After that, you need to take up the side and windshield. First, you will need to turn on the heating in the cabin and make it so that all the ventilation columns are sent directly to the windows swamped. It is necessary to be very careful, as you can overdo it with the air temperature, as a result, due to the categorical difference in the temperatures inside and outside the glass can crack. That is why it is necessary to use warm air temperature.

4. Of course, when holding all these procedures in the cabin, it is better not to have anyone, since the exhaled air will create moisture.

5. It is important to remember that when the result of the absence of condensate should not turn off the recycling of the air, since it will again open the path and accumulation of condensate on the glasses.

6. If the windows also freeze in winter periods, you should not include wipers for cleaning them, as this can lead to breakdowns and scratches on the glass. As a consequence, it is necessary to purchase a defrostator of glass, by which you can get rid of the disadvantage.

3. How to choose a means from fogging glass?

Many car manufacturers produce the installation of heaters on the rear view mirrors and glass. This kind of heaters have the appearance of a fine grid of wires that have quite good electrical conductivity. With the direct inclusion of heating on the wires, an electrical impulse will be supplied, as a result of which it will become transparent.

In addition, in the automotive nature, there is a large number of special chemicals by which the car windows are treated. The principle of operation of such liquids and elements is quite simple, since it is simply necessary to make a smooth surface of the glass, as a result of which the accumulation of moisture will be suspended, as the condensate will be straightforward. Nevertheless, such funds have a weighty minus - they do not work in the winter season, as the drops freeze very quickly.

Another way will be replacing the cabin filter.In his arsenal, the absorbent is always located, which will be happy to absorb all the extra moisture from the air and not to let it in the salon. After the filter is clogged, the moisture will settle on the glasses and are located inside in the form of condensate. If the glass will sweat and with a new filter, then the reason will be covered in the fault of the air recycling valve, which was most likely closed in one closed position.

In addition, some motorists resort to the following: you need to sew a bag, and to pour salt into it and put under the torpedo. Salt is quite hygroscopic, as a result of which it will quickly absorb an extra moisture. It is always important to always remember that the fogging of the glass is a problem that is disturbing absolutely all motorists. If you understand the mechanism of education and the occurrence of condensation, in time to prevent the occurrence of this trouble in time, then the problem overcoming the problem will not be much difficulty. Nevertheless, always at hand there must be a clean rag, which will never refuse to help its owner.

Subscribe to our ribbons in